Keder profile aluminium M 20x46-3

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development. This is simpler than it sounds: let's take a round banner with a 3 m diameter and 1 m height. The circumference is: 3 m x Pi, i.e. 3 x 3.1415 = 9.425 m So the file must first be created at 9425x1000 mm. In addition, 5 cm is needed at the top and bottom for the hem. On the right and left, you should add 10 cm of additional area so that there is enough space for the joint edge. The file size is therefore 9525x1200 mm, of which 9425x1000 mm remain for the visible area. When it comes to the arrangement of the logos, for example, you have to divide the circumference by 3 or by 4 and arrange the logos at this spacing. In our example, that is then 3141 mm for 3 logos and 2356 mm for 4 logos. FAQ about round banners / round ceiling hangers How are the round banners constructed? The round banner as a ceiling hanger consists of two circular keder profiles. The actual cylinder-shaped banner is fastened between the two rings. The upper ring of the keder profile is hung from wire ropes. The banner is pulled into the keder groove of the upper profile with a pole pocket containing an inserted keder tube. The lower ring is hung onto the banner using the same principle and serves as a weight so that it hangs taut. The banner can be pulled taut at the sides and thus hung wrinkle-free. Which diameter should I choose? The diameter is in principle freely selectable. The most common size at trade fair stands is 2 to 5 m diameter. For larger diameters, additional tension rods may be required so that the banner really hangs smoothly. Diameters that are too small are difficult, as the profiles cannot be bent too tightly. The minimum diameter should not be less than 1 m. Which profile should I choose? Up to a diameter of 2.5 m we recommend the 28 profile. From a diameter of 2.50 m we recommend the larger profile (20x46). For rings over 5 m in diameter, the larger 48 profile is also recommended. Which height is suitable? The height is just as freely selectable as the diameter. However, you should make sure that the proportions of the logo or graphics to be printed on the banner suit the cylindrical banner. Here it can be useful to create a visualisation beforehand. We are happy to help you with the calculation and rendering of the round ceiling hangers. A height of 60 to 100 cm with a diameter of 3 m is a good order of magnitude. How many logos fit on a round banner? The number of logos depends heavily on the aspect ratio of the logo used. In general, you can say that at least 3 logos should be used on a round banner so that it is visible from all sides. Usually four or more logos make sense. How heavy is a round banner? The weight is calculated automatically and shown as the total weight in the configurator. Can round ceiling hangers be printed on both sides? Yes, that is possible. For this, a different banner material is used, which has an opaque barrier layer in the middle so that the print does not show through. How are the round banners delivered? The banners are delivered disassembled. This means the ring-shaped profiles are divided into individual segments. The number of segments can be defined as desired. The banner itself is delivered rolled up. How often can the circular profiles be divided? The number of divisions should be as low as possible. The main reason is transport. For smaller diameters up to 1.5 m, dividing into two halves can suffice. A round banner with a 5 m diameter should be divided four to six times. How are the segments reassembled? The individual segments of the circle are joined with so-called splices. These are pushed into the profile and fixed with screws. All necessary accessories are automatically supplied correctly when selected in the configurator. We are happy to advise you personally and prepare an individual offer: 📞 Phone: +49 421 9607314 📧 E-mail: shop@banner-kontor.de

A curved exhibition wall, cut to size. Of course, this can also be a photo backdrop, a sponsor wall or a background for a product presentation. The decisive thing is: you can freely choose the dimensions, quickly change the fabric print, and have a stable system that can really hold its own. Setting up the exhibition walls is easy: a minimum of 2 columns are set up and keder profiles are attached at the top and bottom. The banner is pulled into these profiles. DetailsThe keder profiles are fixed so that the banner hangs smoothly and wrinkle-free. All necessary accessories are of course included. Does the wall then stand stably? Yes, because the round base plates provide the necessary hold. The curvature creates additional stability, which is why small feet are sufficient in most cases. Although you should of course pay attention to a sensible ratio between width and height when planning. The width of the curved exhibition wall is, by the way, almost unlimited. The profiles can be extended further and further by splices. Different radii can also be combined. A printed display wall in a wave shape can therefore be realised. A completely circular construction is also feasible. If you want to create a semicircular meeting area at the trade fair stand, this system is exactly right for you. The print can be on an opaque banner print. This way the graphic wall can be used as a partition for your back office. Or you deliberately choose a slightly transparent fabric to make sub-areas more open. Our LED cantilever spotlights are also ideally suited for the even illumination of the exhibition walls. So you have a lot of design freedom. We are happy to advise you and determine the necessary dimensions and bending radius for you. If required, we can also visualise the result photorealistically in advance.

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development. FAQ about round banners / round ceiling hangers How are the round banners constructed? The round banner as a ceiling hanger consists of two circular keder profiles. The actual cylinder-shaped banner is fastened between the two rings. The upper ring of the keder profile is hung from wire ropes. The banner is pulled into the keder groove of the upper profile with a pole pocket containing an inserted keder tube. The lower ring is hung onto the banner using the same principle and serves as a weight so that it hangs taut. The banner can be pulled taut at the sides and thus hung wrinkle-free. Which diameter should I choose? The diameter is in principle freely selectable. The most common size at trade fair stands is 2 to 5 m diameter. For larger diameters, additional tension rods may be required so that the banner really hangs smoothly. Diameters that are too small are difficult, as the profiles cannot be bent too tightly. The minimum diameter should not be less than 1 m. Which profile should I choose? Up to a diameter of 2.5 m we recommend the 28 profile. From a diameter of 2.50 m we recommend the larger profile (20x46). For rings over 5 m in diameter, the larger 48 profile is also recommended. Which height is suitable? The height is just as freely selectable as the diameter. However, you should make sure that the proportions of the logo or graphics to be printed on the banner suit the cylindrical banner. Here it can be useful to create a visualisation beforehand. We are happy to help you with the calculation and rendering of the round ceiling hangers. A height of 60 to 100 cm with a diameter of 3 m is a good order of magnitude. How many logos fit on a round banner? The number of logos depends heavily on the aspect ratio of the logo used. In general, you can say that at least 3 logos should be used on a round banner so that it is visible from all sides. Usually four or more logos make sense. How heavy is a round banner? The weight is calculated automatically and shown as the total weight in the configurator. Can round ceiling hangers be printed on both sides? Yes, that is possible. For this, a different banner material is used, which has an opaque barrier layer in the middle so that the print does not show through. How are the round banners delivered? The banners are delivered disassembled. This means the ring-shaped profiles are divided into individual segments. The number of segments can be defined as desired. The banner itself is delivered rolled up. How often can the circular profiles be divided? The number of divisions should be as low as possible. The main reason is transport. For smaller diameters up to 1.5 m, dividing into two halves can suffice. A round banner with a 5 m diameter should be divided four to six times. How are the segments reassembled? The individual segments of the circle are joined with so-called splices. These are pushed into the profile and fixed with screws. All necessary accessories are automatically supplied correctly when selected in the configurator. We are happy to advise you personally and prepare an individual offer: 📞 Phone: +49 421 9607314 📧 E-mail: shop@banner-kontor.de

Ceiling hangers with keder profiles are a true classic. The reason is simple: easy assembly and great impact. As is so often the case, the simplest things are the best. A keder profile at the top and bottom, a printed banner in between, two wire ropes for suspension - done. The size is practically unlimited. The available length in one piece for most keder profiles is 6 m. If the banner is to be larger, several profiles can be securely joined with a splice. Even if transport size matters, the profiles can be divided. But this simple technique can do even more. We can also bend the profiles. This opens up completely new possibilities. Two circles make a beautiful round banner as a ceiling banner. Or curved profiles as circle segments combined with columns create an elegant back wall.

You need a new print for your round banner? Then you're in the right place! Please note the version of your profiles.There is the system with round keder or with flat keder.With round keder, there is a pole pocket at the top and bottom of the banner, into which a rope or a tube is inserted. The banner is slid into the curved profiles from the side.With flat keder, a square silicone profile is sewn all around, which is inserted into the profile after assembly.The banner material can be translucent for backlighting or opaque.An opaque material is used for double-sided banners, or when shadows are to be avoided when light falls on the banner from behind.To create the print data correctly, please use this PDF fileThere you enter your dimensions and receive the dimensions for the print file in the lower section.The width corresponds to the circumference (diameter x 3.1415) + 40 mm right and left.The height must also be created with a 40 mm allowance at the top and bottom.

Classic round banner in cylinder shape. With two ring-shaped keder profiles at the top and bottom. Incl. print on opaque material. You can choose between two profile types. The smaller S28 profile can be used up to approx. 3 m. Above that we recommend the 48 profile. The round banner is supplied complete with splices (connectors for the divided full circle), pre-finished print web and at least 4 ceiling suspensions. From a diameter of 3 m we recommend 6 suspensions, and from 6 m 8 suspensions. Round banner|diameter

Keder profile aluminium M 20x46. Versatile applications in trade fair construction, for shopfitting or for modern exhibitions. Combined with our large selection of fabric banner materials, you have a particularly large scope for design.

Keder profile aluminium S universal 28. Versatile applications in trade fair construction, for shopfitting or for modern exhibitions. This slim version is discreet yet sturdy. We bend the profile to your requirements, so wavy or round banners are also possible. Combined with our large selection of fabric banner materials, you have a particularly large scope for design.The banner is slid into the profile from the side with a pole pocket and an inserted keder cord. Alternatively, a tent keder can be sewn on.

Keder profile aluminium M 20x48 with slot profile. Suitable for suspension from the ceiling with wire rope holders and T-slot nuts. Versatile applications in trade fair construction, for shopfitting or for modern exhibitions. Combined with our large selection of fabric banner materials, you have a particularly large scope for design.