Rundbanner

Exhibition banner as a cylinder with tension frame technology. Thanks to its round shape, this ceiling hanger is perfectly visible from all sides. The print can be applied either on the outside or additionally on the inside. Both sides can be replaced separately.

Classic round banner in cylinder shape. With two ring-shaped keder profiles at the top and bottom. Incl. print on opaque material. You can choose between two profile types. The smaller S28 profile can be used up to approx. 3 m. Above that we recommend the 48 profile. The round banner is supplied complete with splices (connectors for the divided full circle), pre-finished print web and at least 4 ceiling suspensions. From a diameter of 3 m we recommend 6 suspensions, and from 6 m 8 suspensions. Round banner|diameter

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development. This is simpler than it sounds: let's take a round banner with a 3 m diameter and 1 m height. The circumference is: 3 m x Pi, i.e. 3 x 3.1415 = 9.425 m So the file must first be created at 9425x1000 mm. In addition, 5 cm is needed at the top and bottom for the hem. On the right and left, you should add 10 cm of additional area so that there is enough space for the joint edge. The file size is therefore 9525x1200 mm, of which 9425x1000 mm remain for the visible area. When it comes to the arrangement of the logos, for example, you have to divide the circumference by 3 or by 4 and arrange the logos at this spacing. In our example, that is then 3141 mm for 3 logos and 2356 mm for 4 logos. FAQ about round banners / round ceiling hangers How are the round banners constructed? The round banner as a ceiling hanger consists of two circular keder profiles. The actual cylinder-shaped banner is fastened between the two rings. The upper ring of the keder profile is hung from wire ropes. The banner is pulled into the keder groove of the upper profile with a pole pocket containing an inserted keder tube. The lower ring is hung onto the banner using the same principle and serves as a weight so that it hangs taut. The banner can be pulled taut at the sides and thus hung wrinkle-free. Which diameter should I choose? The diameter is in principle freely selectable. The most common size at trade fair stands is 2 to 5 m diameter. For larger diameters, additional tension rods may be required so that the banner really hangs smoothly. Diameters that are too small are difficult, as the profiles cannot be bent too tightly. The minimum diameter should not be less than 1 m. Which profile should I choose? Up to a diameter of 2.5 m we recommend the 28 profile. From a diameter of 2.50 m we recommend the larger profile (20x46). For rings over 5 m in diameter, the larger 48 profile is also recommended. Which height is suitable? The height is just as freely selectable as the diameter. However, you should make sure that the proportions of the logo or graphics to be printed on the banner suit the cylindrical banner. Here it can be useful to create a visualisation beforehand. We are happy to help you with the calculation and rendering of the round ceiling hangers. A height of 60 to 100 cm with a diameter of 3 m is a good order of magnitude. How many logos fit on a round banner? The number of logos depends heavily on the aspect ratio of the logo used. In general, you can say that at least 3 logos should be used on a round banner so that it is visible from all sides. Usually four or more logos make sense. How heavy is a round banner? The weight is calculated automatically and shown as the total weight in the configurator. Can round ceiling hangers be printed on both sides? Yes, that is possible. For this, a different banner material is used, which has an opaque barrier layer in the middle so that the print does not show through. How are the round banners delivered? The banners are delivered disassembled. This means the ring-shaped profiles are divided into individual segments. The number of segments can be defined as desired. The banner itself is delivered rolled up. How often can the circular profiles be divided? The number of divisions should be as low as possible. The main reason is transport. For smaller diameters up to 1.5 m, dividing into two halves can suffice. A round banner with a 5 m diameter should be divided four to six times. How are the segments reassembled? The individual segments of the circle are joined with so-called splices. These are pushed into the profile and fixed with screws. All necessary accessories are automatically supplied correctly when selected in the configurator. We are happy to advise you personally and prepare an individual offer: 📞 Phone: +49 421 9607314 📧 E-mail: shop@banner-kontor.de

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development. FAQ about round banners / round ceiling hangers How are the round banners constructed? The round banner as a ceiling hanger consists of two circular keder profiles. The actual cylinder-shaped banner is fastened between the two rings. The upper ring of the keder profile is hung from wire ropes. The banner is pulled into the keder groove of the upper profile with a pole pocket containing an inserted keder tube. The lower ring is hung onto the banner using the same principle and serves as a weight so that it hangs taut. The banner can be pulled taut at the sides and thus hung wrinkle-free. Which diameter should I choose? The diameter is in principle freely selectable. The most common size at trade fair stands is 2 to 5 m diameter. For larger diameters, additional tension rods may be required so that the banner really hangs smoothly. Diameters that are too small are difficult, as the profiles cannot be bent too tightly. The minimum diameter should not be less than 1 m. Which profile should I choose? Up to a diameter of 2.5 m we recommend the 28 profile. From a diameter of 2.50 m we recommend the larger profile (20x46). For rings over 5 m in diameter, the larger 48 profile is also recommended. Which height is suitable? The height is just as freely selectable as the diameter. However, you should make sure that the proportions of the logo or graphics to be printed on the banner suit the cylindrical banner. Here it can be useful to create a visualisation beforehand. We are happy to help you with the calculation and rendering of the round ceiling hangers. A height of 60 to 100 cm with a diameter of 3 m is a good order of magnitude. How many logos fit on a round banner? The number of logos depends heavily on the aspect ratio of the logo used. In general, you can say that at least 3 logos should be used on a round banner so that it is visible from all sides. Usually four or more logos make sense. How heavy is a round banner? The weight is calculated automatically and shown as the total weight in the configurator. Can round ceiling hangers be printed on both sides? Yes, that is possible. For this, a different banner material is used, which has an opaque barrier layer in the middle so that the print does not show through. How are the round banners delivered? The banners are delivered disassembled. This means the ring-shaped profiles are divided into individual segments. The number of segments can be defined as desired. The banner itself is delivered rolled up. How often can the circular profiles be divided? The number of divisions should be as low as possible. The main reason is transport. For smaller diameters up to 1.5 m, dividing into two halves can suffice. A round banner with a 5 m diameter should be divided four to six times. How are the segments reassembled? The individual segments of the circle are joined with so-called splices. These are pushed into the profile and fixed with screws. All necessary accessories are automatically supplied correctly when selected in the configurator. We are happy to advise you personally and prepare an individual offer: 📞 Phone: +49 421 9607314 📧 E-mail: shop@banner-kontor.de

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development.

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development.

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development.

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development.

A classic for the trade fair stand or at the POS: the round ceiling hanger with fabric banner and 4c print. Simple and lightweight relative to its size. Two circularly bent keder profiles define the shape. The circles are usually segmented, i.e. divided into transportable segments. The upper ring is hung and the banner is threaded in. The lower ring is pushed onto the lower hem of the banner and hangs from the banner. The assembly is carried out in this order. The upper ring made of the keder profile is simply left open at one point so that the banner can be threaded in here. The lower ring can be pulled onto the lower, hanging hem with the keder tube segment by segment. The joints of the profiles are stabilised with a splice and additionally screwed. Geometrically, the layout of a round ceiling banner must be created on a cylinder development.

Circular tension frames are an absolute novelty and offer entirely new possibilities in the design of trade fair stands or in shopfitting. The newly developed flat keder profile with double-sided covering can be bent over both the X axis and the Y axis (see images) to any radii from 500 mm according to customer requirements. This means a full circle made of two semicircles can also be realised for a tension frame. The profile can also be hung with a wire rope holder and used as a kind of mobile. The finishing of the flat keder in a circle is implemented perfectly with our CNC-controlled machines. The result is a clean and wrinkle-free tension for the banner print. Of course, the round tension frame can also be used excellently as a decorative element with a wall mounting.